dimewall01

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/salisbury-door-locks-replacement-near-me/

How to Replace Door Locks Door locks are the first security measure against unauthorized access to your home The signs of wear and tear and also instances like moving into a new residence or breakins can necessitate the necessity of replacing your lock To begin you must determine the size of your cylinder using the distance between the adjustment screw and the center of the cylinder knob replace lock on upvc door will enable you to purchase the correctsized lock Deadbolt Installing a deadbolt is a excellent way to protect your door against intruders The bolt extends into the strike plate on the doorframe when locked making it much more difficult for burglars to break in through the door A singlecylinder deadbolt is activated with a key on the outside and a thumbturn piece situated inside Deadbolts are only effective when its properly installed though First youll need to find out if the door has a hole to install deadbolts or if it has to be bored With the template included with the lock installation kit mark the spot of the deadbolts hole on the doors surface Utilize your tape measure to determine the height of the deadbolt Mark this high point on the doors edge Use the speedsquare to draw a straight line across the mark that you made for the bolt hole Then use a drill to bore this area until the hole is on the other side of the door This may take some time Then sand down the hole and the edge of the door so that it is smooth Its also a good idea to paint or stain the door at this point Remove any visible screws from the deadbolt This will reveal the front and rear assembly of the deadbolt as well as its internal bolt Then remove the bolt and replace it with an alternative bolt that matches your door hardware You will need to unscrew the bolt from a setplate Then youll need to chisel the door frame for the strike plate If your strike plate isnt aligned properly its likely because the previous installer didnt mortise it correctly or a weatherstripping popped up and changed the strike position To correct this issue it is necessary to remortise the strike plate and the deadbolt Close and lock the deadbolt after youve completed this step Test the deadbolt by closing it and locking it after the bolt has been extended into the strike plate Knob When a door knob is worn out it could make your home or business less secure It could make it difficult to open or close the door which is why its recommended to replace the knob Replacing knobs is an easy DIY task that should not take more than 30 minutes to complete Use a screwdriver or pliers to remove any old knobs or handles Be careful not to damage the other components of the door Before you begin youll want to spray WD40 or some other dry lubricant onto the mechanism of the door knob This will help the new lock slide effortlessly when you turn it It is essential to choose a quality knob and handle that match your current doors to ensure that the lock is operating properly If you dont have a matching doorknob and handle youll need to buy a replacement Before you begin the replacement process take a look at the knob that was previously used to determine which screws are keeping it in place If there arent any screws you can make use of a screwdriver and wedge it between the cover plate and the hidden screws plate and remove it After youve removed your knob that was previously used look it over for any signs of damage or rust Youll have to scrub it up if there are any scratches or dents however you shouldnt need to do anything major when the knob is in good working order Install the new knob It is important to first look over the two knobs to make sure that you are choosing the right one for the door Youll want to pick one with an extended rod that is designed to lock with the rod mechanism on the second knob Once youve positioned the new knob in the hole in the door and then carefully slide it into the latch Test the spring by pressing it repeatedly The latch should spring back up every time Install the second knob and secure it to the rod mechanism of the first knob Thread the long screws of the doorknobs interior through the holes for cylinders on the exterior knob and lock it into place Latch A latch is a piece of metal that extends through the doorjamb to secure it closed The latch is operated either by a knob or handle on the interior of the door or by a thumbturn on the outside A latch can be secured using deadbolts to prevent intrusions from piercing the glass It can also protect against intentional or accidental closing by children or animals A latch can be installed with one cylinder deadbolt or a double cylinder deadbolt according to the security level you prefer Installing a deadbolt is exactly the same as installing a latch however there are some differences First you must measure the setback of the doorjamb with a tape measure to be sure the new lock will fit The setback is measured from the edge of the doorjamb up to the center of hole for the latch plate A standard setback is 2 38 to 2 34 inches If you have a higher setback you may have to purchase a larger latch at a hardware store or locksmith The next step is to drill an edge bore hole in the doorjamb for the latch plate Use a chisel for chiseling out the mortise of the latch making sure its large enough to allow the faceplate of the new latch to be close to the doorjamb Place the strikeplate on the floor to ensure its placed correctly If the strike is too high you could push the door back or apply pressure with an iron tire or crowbar This could cause the doorjamb to crack This can be repaired by drilling a new hole into the doorjamb then removing the core from the old one The final step is to put in the new strike plate which is done by screwing it over the screw holes that are already in place Use wood putty afterwards to fill in any old bolt holes or screw holes that arent being used After the putty has dried you can sand it down to give it a a professional finish Strike The piece of metal that connects the latch and deadbolt when the door is shut is an electric strike It is a vital component of the overall security of a lock since it helps keep the door shut and offers additional resistance to force or kicking applied to the door If a door is equipped with an electric strike it can be opened by a key or the control unit that controls the electrical impulses Traditionally installing an electric strike meant cutting a small portion of the doorjamb in order to release the latchbolt of a cylindrical lock from the pocket within the strike This change can be a drawback when it comes to the appearance of openings as well as exposing the keeper mechanism and latchbolt to unauthorized users Recently a number of electric strike manufacturers have created a No Cut type of strike that doesnt require a cutout in order to operate The strikes use a unique design that allows the latchbolt and keeper to slide into the strike pocket without damaging the doorjamb faceplate The strike has an internal ramp that lifts the keeper and latchbolt when it receives an electrical signal from a reader or controller The latchbolt and keeper are lifted higher up the ramp by the retract When the door is closed the deadbolt remains retracted and the latchbolt retracts into the keeper Installing an electronic strike is a straightforward procedure particularly when youre replacing an older strike If youre planning to upgrade an access control system to an electric strike you must ensure that your new system is compatible Also you must ensure that the strike is properly connected to your access control system and is set up for failsafe operation Upgrade your strike plates with heavy duty strike plates to block unauthorised entry The plates are made of up to six screws of three inches instead of the usual two screws of threefourths of an inch The longer screws make it more difficult for someone to break the frame and reach inside to turn the thumb turn piece of a single deadbolt cylinder