eggparade5

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/basingstoke-windowrepair/

How to Replace Door Handles Door handles are an essential element of your homes decor A new handle will elevate your home and bring your decor to the present Over time the knobs on your door could become stiff or even break These are indications that its time to replace them This guide will help choose the right door handle replacement for your home Door Knobs Door handles can enhance the look of your home while also making it easier for people to open and shut doors They are available in a range of finishes colors and types to complement your decor If yours is beginning begin to show signs of wear or you just want to upgrade replacing them is relatively simple and can be completed in just a few steps The first thing you have to find is the spindle or shaft through which the knob is affixed to the door Some have a small hole that you can put the screwdriver with a small diameter to remove the set screws that hold the handle in place Some have a slot or hole where can be used with the flathead screwdriver on a springactivated pin also known as a detent This pin releases the latch mechanism and allows you to pull or push the knob Once you have the spindle or shaft in your hand remove the old knob and replace it Be sure to align it correctly and test to see that the latch works properly before tightening the new set screws After replacing the knob place the rod that is attached to the latch over the doors hole Lock it in place using the rod system on the second knob Make sure the holes are aligned and then thread in the screws for the latch plate and tighten the screws upvc door handles opt for the smooth or brushed finish on their door hardware to create modern sleek design that matches other furnishings in their homes Others prefer a more rustic design which is great for rusticstyled rooms If you have members of your household with mobility limitations you may want to consider choosing a rim lock or lever knobs for doors that require less pressure to operate Other aspects are being taken into consideration more and more in the design of door handles Accessibility and control of infections have been major considerations when it comes to developing new handle designs For example certain handles handle designs can be operated by an arm Latch The latch that holds the door handle open may wear out as time passes It is simple to change the latch on your door handle This will make huge differences in how it opens and closes Depending on what type of handle you are using the latch could be a separate part or an integral part of the knob In either case the same process for removing and reinstalling will apply Getting the old latch out of the way is relatively simple especially if your door handle is equipped with whats known as a magic button This tiny pressureslot found on the side knob is what you need to press in order to pull the latch out of the handle If your handle does not have this button the first step is to take off any cover plates that sit over the latch plate They are typically circular or rectangular and can be removed by using a screwdriver to pry them off of the handle Some have a small hole in them where you can slide your screwdriver whereas others snap off Then loosen the machine screws that attach the inner plate and latch to the door handle These are the screws with a sharp tip You will have to store them in a secure location to use them again in the next steps Once the screws are removed you can remove the latch plate and mechanism out of the doors hole and set it aside Then you can begin to install the new latch Install the latch plate into the door hole and secure it using the hardware supplied Make sure the square pin on the interior of the latch is facing the latching mechanism inside the handle and that it lines up with the other screw chambers in the door handle Then attach the latchs exterior plate using the screws provided Strike Plate It is not uncommon to replace a door handle because it is loose or doesnt lock properly This is usually due to malfunctioning parts of the latching system such as a strike plate that is too small or has moved upwards or down on the doorjamb as time passes This easy project allows you to replace your old strike plate with a longer new one that can provide greater security and ensure that your door stays shut To determine if the issue is due to the strike plate apply some lipstick or a similar marking material to the bolt that is used to latch Close the door then try to latch it If the mark is lower than the strike plates hole it means that the plate is too small and the door wont latch If the mark is higher than the strike plate hole its likely that the strike plate has been moved up or down the doorjamb Depending on the door You may be able to simply attach the new strike plate into the existing one using the screws included with it However you might need to drill holes prior to drilling and then chisel some of the wood to make sure its a snug fit If this is the situation make sure you dont chisel out too much wood or youll damage the integrity of the doorjamb You can also consider installing a new strike plate which will give the lock a more secure grip on the door and requires more force to open it Typically it requires two longer screws that secure the strike plate to the door frame Youll have to remove the old strike plate before drilling and chiseling the wood to make room for the new one This hardtofind strike plate is designed to be used with antique rim locks and is made of durable solid brass in an extremely thick This kit includes wood screws and machine screws so you can choose the right hardware to suit your requirements Be aware that wood screws have a pointed tip while machine screws are more blunt