giantrobin0

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/west-bromwich-window-lock-repairs-near-me/

How to Do a Door Lock Change The change of your door lock is a simple and inexpensive way to increase the security of your home However the procedure is not for everyone It requires some skill and patience The cylinder is inside the knob body The cylinder is responsible to recognize the key when it is put into the lock The old lock can be removed The first step is to remove the lock that was previously in place Its a easy process but you must keep certain things in your mind Make sure your new lock is compatible with your door This will ensure that it fits properly and does not leave a gap around the deadbolt plug or latch Once you have removed the latch plate look for two bolts or screws on the inside of the casing that hold the casing and the halves of the lock Unscrew them using a screwdriver then pull the lock out of the door If you have a mortise locking system there is an anchor screw that connects the handle to the spindle Take off the doorknobs by removing the screw using the help of a screwdriver It is also recommended to remove the latch and deadbolt plug from the hole in your door jamb Install the new lock If youre replacing a mortise you should determine the distance between your locks case and your door edge to make sure that your new lock fits You may want to replace your lock for a variety reasons for instance if you suspect that someone else has the key or if you have a new roommate You can save money by deciding to remove the lock yourself instead of hiring a professional Its much easier than people think and can be done in a matter of a few minutes Start by removing the trim and handle from the door Then pry the trim loose using a flat screwdriver You should be able twist off the majority of it In some instances you may even be able remove the handles completely Next look for a hole on the inside of the handle and then insert straightened clips into it This will activate the release mechanism allowing you to take off the handle Look for a small tab on the interior of the lock and press it with a screwdriver that is flat After the spindle is removed you are able to take off the cylinder and housing Making a choice for a new lock There are a lot of options available when it comes to choosing a new lock Consider the different types of locks and select one that fits the style of your door Take into consideration the backset which is the distance between the edge and the middle of lock hole Also think about the cross bore which is a small hole in the middle of your doors frame Select a lock that is suitable for the door thickness and the swing The majority of door locks have been assessed by BHMA and the American National Standards Institute to provide you with an idea of how well they are able to withstand the rigors of use and how difficult they are to pick or disable A grade 3 lock might be ideal for a quiet urban apartment complex whereas an entry grade lock could hold up better to the traffic near a busy storefront on a busy city street Most smart door locks require a digital code to open If youre worried about hacking or other security concerns seek out an expert locksmith or your local police department to get advice Replace the cylinder If the cylinder of your door lock is damaged or broken you can replace it in just a few minutes with a simple doityourself project The key is to choose the correct cylinder and follow the steps that accompany it First you must remove the knob or handle if it is present Then using a screwdriver unscrew the trim that surrounds the lock cylinder After the trim is removed you can access the screws that keep the cylinder in place and remove them using a flathead screwdriver The cylinder is then gently pulled from the door Be sure to take measurements of the length of the new cylinder prior to putting it in place With an instrument measure the distance between the cylinders center and its left and right side Then buy another cylinder that has the same measurements This will stop the cylinder from snapping which could happen when the door is kicked in or when the key gets stuck inside If you have a replacement cylinder put it in the door and turn the key This will ensure that the cylinder is aligned with the carrier which is normally located on the outside of the lock Then you can loosen the set screw which should be a few turns inside the head You will also need to loosen the screw in the edge of the door which secures the case if there is one You can replace the cylinder that was used to lock your old lock with a new one by inserting it into the case and tightening the set screws You must also install the bracket that connects the cylinder with the stem of the lock indicator and this can be done by pulling up three small tabs on the back of the cylinder using needlenose pliers Attach the smaller bracket to the back of the cylinder Then you must install the strike plate and latch plate as well as the retaining ring that is connected to the top of the lock the cylinder Installing the new lock Start by measuring the doors width if you are replacing an existing lock Most locksets for residential use are designed for doors with a thickness of 1 38 to 34 inch If link home is more thick you will need an extrathick door kit that includes longer screws and longer tail pieces for door knobs or spindle extension for deadbolts The majority of locks come with a thorough installation guide to help you Before beginning you must read the instructions to make sure youve followed all the steps The guide will also provide you with an idea of the level of skill required to accomplish the task You might want to ask a friend who has had experience in changing locks for help if you are changing locks for the first time Before installing the new lock its a good idea to cover the holes with tape the old hardware This will stop the screws from falling out of the holes and will safeguard any tile you may have put in the area It also shields your tiles from any damage caused by rust dirt and grime SECURAM Touch includes a strip of masking or gaffer tape but you can make use of any tape you have After you have removed the screws that hold the locks inner half to the outside take the lock off immediately This must be done quickly to prevent the lock from closing accidentally and damaging the mechanism Fit the new latch bolt in the upper cross bore of the new lock if it has one Make sure you put it in the right location which is marked by an arrow Next fit the latch plate over the bolt and screw it into the correct position Screw the deadbolt to the door jamb Test the deadbolt by throwing it a few times to ensure that it extends all way through the strike plate and is completely secured If youre using an electronic smart lock make sure to follow the instructions to program it This involves downloading an application and entering your email address verifying your identity and then connecting to the wireless network to add your device