grousedoubt6

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/poole-door-locks-replacement-near-me/

How to Replace Door Locks Door locks are the first protection against unauthorised access to your home Signs of wear and tear and even instances such as moving into a new residence or burglaries may trigger the necessity of replacing your lock You can determine the size of your cylinder by measuring the distance from the center of the knoblock cylinder to the adjustment screw This measurement will allow you to purchase the appropriate lock Deadbolt If youre looking to ensure that your door is safe from criminals its a great idea to install a deadbolt When the bolt is extended into the strike plate of the doorframe it makes it harder for an intruder to get through the door A singlecylinder deadbolt is activated by a key located on the exterior and the thumbturn mechanism located on the interior Deadbolts are only effective when its properly installed though First youll need to determine if the door already has a hole for a deadbolt or if it needs to be bored out With the template included with the lock installation kit mark the location of the hole for the deadbolt on the doors surface Use a tape measure to determine the height of the deadbolt Then mark the height on the edge of the door You can then use a speed square to draw a straight line across the mark you made for the bolt hole Then using the power drill drill through the hole until it reaches the opposite side of the door It could take a few minutes Sand the hole and the door edge to make it smooth Its also recommended to paint or stain the door at this point Remove any screws that are visible from the deadbolt This will reveal the rear and front assembly of the deadbolt as well as its internal bolt Then loosen the bolt and replace it with a new bolt that matches the door hardware The bolt is typically connected to a setplate which you will need to unbolt After that you will need to chisel the area for the strike plate on the door frame If your strike plate is misaligned its likely that the previous installer didnt correctly mortise it or a weatherstripping was installed and changed the strike position Youll need to remortise the strikeplate and possibly even the deadbolt to fix this issue Close and lock the deadbolt once you have completed this step Make sure the bolt extends into the strike plate and then test the key to ensure it closes and opens effortlessly Knob If a door knob is damaged it could make your home or business less secure It can make opening or closing the door more difficult which is why it is an ideal idea to replace the knob Replacing a knob is a relatively easy DIY task that should not take longer than 30 minutes to complete You can use a screwdriver as well as pliers to remove the knob or handle However be careful not to damage any other parts on the door Spray WD40 or another dry lubricant on the mechanism of your door knob before you begin This will allow the new lock to move smoothly when you turn it Its important to use the best knob and handle that is compatible with your doors currently in order to ensure proper operation If theres no match youll need to buy a replacement doorknob and latch plate Before you begin the replacement take a look at the knob that was previously used to see what screws are holding it in place If there are no screws to hold it in place you can use a screwdriver to insert the cover plate into the hidden screws plate After taking the knob off take it apart and look for signs of rust and damage Youll need to clean it up if there are any scratches or marks however you dont need to do anything major If the knob is in good shape replacement door lock to install the new knob Before you do that look over the knobs youve chosen to ensure youre choosing the right one for your door You should select one with an extending rod thats designed to lock into the rod mechanism of the second knob Once youve put the new knob into the hole then slide it into the latch Test the spring by pressing it down repeatedly The latch should spring back up each time Then put in the new knob and connect it to the rod mechanism on the first knob Thread in the other long screws from the knobs interior through the hole in the cylinder of the doorknob outside and secure it Latch A latch is a metallic piece that extends out into the doorjamb in order to hold it shut The latch is operated either by a handle or knob located inside the door or a thumbturn on the outside A latch can be secured using deadbolts to prevent thieves from breaking through the doors glass It also helps protect against accidental or intentional closing by animals or children You can install the latch using either a singlecylinder or doublecylinder deadbolt depending on the level you prefer for security Installing a latch follows the same steps like installing a deadbolt however there are a few distinctions To make sure that the new lock will work first determine the setback of the doorjamb with a tape measure The setback is the distance between the edge of the doorjamb to the middle of the hole to accommodate the latch faceplate Setbacks for standard latches are 2 38 to 2 34 inches If your setback is higher it is possible to purchase a latch that is longer from a hardware or locksmith store Then make a hole for a latch plate into the doorjambs edge Utilize a chisel to smooth out the latch mortise making sure its deep enough for the faceplate of the new latch to sit close to the doorjamb Place the strikeplate on the floor to ensure that its positioned correctly If the strike is too high you can kick the door in or apply pressure with a tire iron or crowbar This can also cause the doorjamb to break To remedy this issue the strike can be lowered by drilling a new hole in the doorjamb and cutting out the core of the old hole Installing the new strike plate is the final step This can be accomplished by fixing the new plate to the existing screwholes Utilize wood putty to fill in any old screw holes or bolt holes that wont be used Once the putty has dried you can sand it until it has a smooth finish Strike An electric strike is the metallic piece that holds the deadbolt and latch are engaged when the door is shut It is a crucial component of the security of a lock because it helps keep the door shut and also provides additional resistance to force or kicking applied to the door If a door is fitted with an electronic strike it can be opened by using a key and the control unit that regulates the electrical impulses In the past putting in an electronic strike was as simple as cutting a portion of a doorjamb in order to remove the latchbolt on a cylindrical lock from the pocket within the strike This modification is not only unattractive however it also exposes the mechanism for the latchbolt and keeper to unauthorized users Recently a variety of electric strike manufacturers have developed a No Cut type of strike that does not require a cutout for operation The strikes have a unique design that allows the latchbolt and keeper to slide into the pocket without causing damage to the doorjambs faceplate The strike is equipped with an internal ramp which lifts the latchbolt as well as the keeper when it receives an indication from a reader The retraction of the keeper and latchbolt pushes them up higher on the ramp which locks the door When the door is closed the deadbolt is retracted and the latchbolt retracts into the keeper Installing an electric strike is an easy process particularly when you are replacing the strike on a previous door If you are upgrading an existing access control system to an electric strike you must make sure that the new system is compatible You will also have to make sure that the strike is properly connected to your access control system and is configured to operate in a safe manner One way to protect against access by unauthorized persons is to upgrade the strike on your doors to a highquality strike plate These plates use four to six screws of three inches instead of the two threefourth inch screws that are typically employed in regular strikes These screws are longer and make breaking the frame to reach the thumb turn piece on a single deadbolt for a cylinder more difficult