hubcaptanker7
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.thekeylab.co.uk/fiat-car-keys/
Reasons Your Fiat 500 Key Fob Wont Work A key fob for the Fiat 500 makes it easy to open doors and start your vehicle There are a myriad of reasons the fob could stop working These include a dead battery damaged receiver module water damage issues and interference This listing is for an NEW replacement Fiat Flip Key Remote that is similar to the Ilco brand It has to be professionally programmed click here to find local locksmiths in the automotive industry This remote includes lock unlock and trunk buttons Dead Coin Battery The most frequent reason that your 500 key fob doesnt work is a dead battery Modern key fobs have a very limited operating range and should be within some feet of the vehicle in order to function If youre far away from your vehicle and you press the key fob button the car wont respond and will display a Key Fob Not Detected message in the instrument cluster If replacement fiat key happens replace the coincell battery Part Number CR2032 by a fresh one of a reliable brand like Panasonic Duracell or Energizer You can find them at your local hardware store or online You can test the battery in the coincell by pressing the buttons while youre standing close to your Fiat 500 The car will blink its parking lights and the key fob should work the lock and unlock switches If your fobs key isnt working after replacing the battery there may be water damage which is preventing it from interacting with the module inside your vehicle Water damage can happen in a variety of ways from an accidental splash to submerging the fob in salt water at the beach If you suspect your fob was exposed to water try putting it in a dry rice bag to pull the moisture out If this isnt working youll have to get your fob changed by an auto locksmith or a dealer Water Damage Water damage can occur if you immerse the fob into the ocean or wash it in a washing machine Saltwater can cause the circuit board to become shorted and eventually fail Its not a good idea to let the fob get wet however but dont give it up when you accidentally drop it in water or forget to remove it from your pants pocket First remove the battery from the fob Clean the electronic chip with isopropyl ethanol or a similar product and then dry it thoroughly before replacing the battery Next try the fob and see if it works If the key doesnt work it may need to be programmed again This is typically done by a dealer or professional auto locksmith If the key you have is older and is not programmed to work with your vehicle you will need to replace it completely This is a straightforward process that can be completed by a professional automotive locksmith The locksmith will need the key to be cut to match your cars ignition They will also need to program the fob into your cars system Its a simple and affordable process that can be completed on the same day Receiver Module Issues One of the simplest reasons your 500 key fob may stop working is because its out of range The remote has a maximum range of 30 feet Therefore if you are too far from your vehicle it will not respond to your commands You can fix this by moving the remote closer to your vehicle until it responds If your fob does not work after replacing the battery inside the coin which is also called a button watch or button or button it may be due to a malfunction on the circuit board inside In most cases reprogramming the fob will solve the problem There are instructions on how to do this for the majority of vehicles by searching YouTube or checking out the owners manual It may be necessary to replace the metal clips that hold the coin batteries in the correct position If they lose tension it can prevent the coin battery from sitting properly and can cause your remote to malfunction In rare instances the fob could be out of connection with your vehicle as a result of hardware or software problems This could be a huge issue but you are able to usually fix it by visiting an auto locksmith to have them reprogram your fob In certain instances they may have to reinstall the software in your body control module too Interference Interference can also cause the key fob to not be able to receive or transmit a signal This could happen if the key fob is in proximity to an electronic radio transmitter cell phones and radar detectors or another source of electromagnetic radiation Other reasons the key fob may not function could be due to a weak connection to the buttons and internal chip or water damage If the key fob suddenly stopped working out of the blue or after trying every option at home to fix it eg replacing batteries reprogramming or using the spare key fob you may have a damaged receiver module on your 500 The receiver module located beneath the dashboard is able to pick up radio frequency signals from your key fob It then converts them into electronic commands that the vehicle interprets Theres a simple method to reset the 500s onboard system including the keyfob Disconnect the 12 volt battery for approximately 15 minutes by disconnecting the negative cable first then the positive cable Then reconnect the battery This will eliminate any remaining electrical charge and restart the cars computers This could help get your key fob working again If the issue continues you should seek the advice of an expert technician They can identify the exact cause of any issues