jeepweapon21

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/cambridge-windowrepair/

Door Hinge Repair Cambridge Door hinges are an insignificant aspect that can make a big impact on the function and look of your doors Replacing squeaky hinges is a simple and affordable upgrade that can boost your homes curb appeal Petroleum jelly or bar soap is a common method to fix hinges that are squeaky Rub the soap or petroleum jelly on the hinges and let it dry to coat it with a coating Replacement Hinges Hinges are a tiny component that can cause a substantial amount of damage when they wear out or break The good news is that hinges can be replaced without the need for special tools It is essential to select the right hinge for your home This will ensure that your door closes and opens smoothly If the hinges on your door arent working properly consult an expert to fix them as soon as is possible A faulty hinge can cause the door to swell or pull away from the frame This is typically caused by poor use or weight too much Lubricating your hinges is vital to prevent this This will stop the hinge from rusting or squeaking and will extend the life of your doors There are several types of hinges and each type has its own benefits and disadvantages The most common hinge is the butt joint which is secured to the door using pins on both sides This hinge is ideal for doors with light weights since it doesnt require much strength to open or close The butt joint is more prone to damage than other hinge It is recommended to use continuous piano hinges for doors that are heavier This type of door hinge is able to span throughout the length of the door It allows the door to be opened and closed quickly This type of hinge has the benefit of not needing the use of a center support and is more robust The pivot for the storefront door is another popular type of hinge It allows doors to pivot from a single point at the top or bottom of the door These are usually found in commercial locations and can be a challenge to repair if damaged A professional can assist you with this issue by mounting the new pivot hinge or changing the existing one The cost of hinges will vary according to the type Loose Hinges If hinges arent tight they will cause the door to hang crooked and may even start scraping against the floor which is annoying at best In general loose hinges are a issue that can be fixed by any homeowner who has just a few basic tools In many instances tightening the screws on the hinges will fix the issue However in some instances the screws may have become stripped and they wont be able to stay tight If the screw holes are stripped you will have to drill them out and then plug them in with wooden dowels or gluecoated wooden matches To prevent your door hinges from becoming loose you must relubricate them and tighten them regularly Check for any signs of damage on the hinges If you notice any cracks or chips on the metal it may be the time to replace your hinge Its also recommended to replace the hinges if you find that theyre beginning to stick or bind when you close and open the door The most common reason that hinges on doors become loose is due to wear and tear resulting from constant use without proper tightening and lubrication This is particularly true for doors that are frequented by children because they can hang from the handles of the door or swing the door on the hinges This can cause the hinges to loosen and could even fall out If the hinges are loose for a short amount of time you can usually just tighten them with the help of a screwdriver However when theyre loose for a longer time the constant movement of the hinge plate and screws will eventually enlarge the holes the screws enter This will eventually make it impossible for the screws to stay in place and they will eventually be stripped rendering them ineffective To fix this simply dip the bare end of a wooden match into regular carpenters adhesive and then tap it a bit with a hammer to work the glue into the hole as far as it is possible It is likely that youll have to insert several matches coated with glue to fill the hole Rusty Hinges Rust is a typical issue for hinges used on doors especially on older doors It can make hinges look bad and can cause them to break and fail This poses dangerous to those who use the door It is possible to save an old hinge by doing some work The first step is to take the hinges from the door and then clean them of any gunk After the hinges have been cleaned they can be oiled and used again In the past hinges that were of low quality were constructed of steel and iron that would often rust but modern doors are often made of brass or metal alloys that dont get rusty as easily However some people still prefer oldfashioned iron hinges for their beauty and durability even though they are more susceptible to rust than modern hinges The best way to avoid this is to prevent the hinge from rusting in first place It is simplest to clean the hinges on a regular basis with steel wool and water especially when they are damp If you do this regularly it will lessen the chance of rust becoming as much of an issue for your door hinges If youre looking to take it a step further you can use stainless steel hinges In contrast to iron stainless steel will not rust and can provide your home with modern look If you arent able to replace your hinges the best thing you can do is periodically clean them and then grease them If you are taking off hinges make sure to remove them completely to access all the places to scrub off any corrosion Once the hinges have been cleaned you can apply a mixture of oil and vinegar to lubricate them and protect them from corrosion This is an inexpensive and simple solution that is easily accessible in many homes and is worth a shot before you consider replacing hinges Doors that wont shut Sometimes doors can become misaligned in time because of the normal expansion and contraction of wood If upvc windows cambridge RepairMyWindowsAndDoors occurs the door might catch on the corners of the frame or catch on the latch when you attempt to shut it A little bit of work can often resolve these problems If you can tighten the hinges and fix the issue the door will close properly again Start by inspecting the hinges for loose screws Screws that are loose can cause a hinge to sag and create an opening between the leaf of the hinge and the jamb This could cause the latch to not reach the strike plates hole and lead to a jammed door To fix this issue remove the hinge screw and slide a piece cardboard we make use of the back of old legal pads as a guide between the hinges and the door jamb Fix the hinge This will widen the gap on the hinges side and narrow it down on the latch side and allow the latch to be free of the strike plate Repeat the procedure if the problem is resolved If tightening the hinges and using longer screws to correct the alignment of your strike plate holes still doesnt solve the problem you may need to hammer or shim the strike plate to force it to align with the hole for latching If this is the case a little amount of wood filler and paint is often enough to disguise these changes Longterm use or physical damage can also cause the strikeplate to be warped or curved and cause it to strike the edge but not go far enough into the hole to keep the door shut To test for this apply lipstick to the latch and place the strip of masking tape onto the strike plate Close the door then open it The lipstick should leave an impression on the tape at the point where the latch is able to meet the strike plate hole If the mark is lower than the hole this means that the latch must be moved up