laketest37

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/patio-door-repairs-caterham/

Patio Door Lock Repairs Over time patio doors go through wear and tear which can lead to locks that fail There are a few easy steps you can take to ensure the security of your uPVC door If its resetting the lock or cleaning the mechanism that locks these simple fixes will make your home more secure Clean the Lock Patio doors are great for letting the outdoors in and keeping out the elements However they could pose risky for security in the event that the lock isnt working correctly With time wear and tear hot and cold weather dirt and debris can cause your patio door lock to become difficult to operate With some minor maintenance you can ensure that your patio doors locks always function correctly It is important to first clean the patio door lock and all moving parts This will help get rid of any grime or coatings that may be preventing your lock from functioning effectively Start by wiping all the moving parts of the lock for your patio door with a wet cloth Then you can use a scouring paper or a rough damp cloth to scrub the dirtinfested areas of the frame and door It is recommended to wipe the entire lock with a dry cloth to remove any remaining dampness and allow it to air dry prior to applying it to the next time If you have a patio door that uses a pin tumbler latch mechanism it is possible to apply lubrication to the lock by applying powdered graphite to the key or by using a lubricant made of Teflon such as WD40 MultiUse Product This type of lubricant can be easy to apply and doesnt break down over time If you are unable to find the right lubricant for your needs you could try using a pencil that has an extremely thick tip Put the pencil into the lock and move it around a bit to distribute the graphite Tracks for sliding patio doors require regular maintenance to ensure theyre free of dirt dust and other debris They are particularly susceptible to snow and ice which can cause them become stuck or slack and make it difficult for your patio doors to open and close Sliding patio door track rails and rollers can be cleaned by removing any weather stripping that is damaged or dirty and then cleaning it before replacing it The same applies for rollers on patio doors which can be cleaned and sprayed with nonstick lubricant to help them move freely Lubricate the moving parts uPVC French Doors like sliding patios operate with 3 to 4 or occasionally 5 point locking mechanisms These include the lock cylinder and handle that is operated by a key They also require maintenance specifically lubrication on the moving parts This can be done using an oil that is thin never WD40 and should be done every year If hinges that are sagging arent the reason the door could be skewed and catch or rubbing against the strike plates hole in the frame Remove the strike plate and use a sharp tool to enlarge its mortise This will allow the latch to fit into the hole and prevent it from rubbing against the frame Once the cylinder is cleared of the way and out of the way measure its width using a book or piece of wood that can fit into the gap between the adjustment screw and the lock The outer dimension is measured from the outside of door to the center cylinder The inner dimension is measured from the center adjustment screw to the end cylinder Verify the locks width If your patio door latch is difficult to turn even after cleaning and lubricating theres a possibility that its out of alignment with the strike plate hole Verify that the door is properly balanced and whether the hinge screws are tight but in many cases moving the strike plate up or down can correct the issue The latch might not work properly if the strike of the lock is not large enough In this situation you need to widen the opening with an hammer and chisel Then test the latch so that it does not rub against the jamb frame of the door or get caught the frame Before buying a replacement lock you should first identify the type of mortise lock you have This can be done by looking at the faceplate and observing whether it is round or square Examine each screw hole in the existing lock and note the size This information will help you find an alternative that is the same width and is a perfect fit for your existing hole Youll want to identify the mortise lock and examine it for bends scratches or other damage that need to be repaired A badly damaged or bent latch is more likely break than one thats been used much so be sure to replace the lock with a new secure and safe version when you spot any indications of damage or wear Once youve decided on the kind of lock replacement you require Now its time to begin the actual repair The old spindle and handle should be removed from the patio door Introduce the new handle Start by putting in the handle inside aligning it with the spindle and then securing it by using the two screws or bolts that hold it Install the exterior handle after the interior handle After youve completed these steps test the handles to ensure that they can be shut and open easily and that the latch is in contact correctly with the strikeplate Check the Doors Strike The strike plate and the door latch are two pieces that work together in order to lock the door If they are not aligned properly and the latch isnt latching the door properly This issue is usually simple to repair Check the holes for receiving of the strike plate to ensure they are free of obstructions such as dirt or plastic plugs Loosen the keeper screws holding the strike plate in position This allows it to move vertically but not separate it from the frame Then adjust the strike plate to ensure that its holes for receiving are aligned with the latch hooks on the door latch Once the strike plate is adjusted then tighten all screws and test whether the door shuts smoothly These plates are difficult to reach for homeowners who have sliding patio doors However they are essential to secure and unlock your door These metal plates are usually placed on the top and bottom of the door jamb where they support the doors latch The door latch is inserted into the strike plate and it creates the seal If the strike plate is damaged rusted or not installed correctly it can stop the latch from locking the door securely Repair My Windows And Doors for the patio door lock to not close or not close is a misalignment of the latch and the strike plate This can be checked with the lipstick test Apply some lipstick on the outside of the deadbolt and then cover it with masking tape When you close the door the lipstick will leave a mark on the tape that will show exactly where the latch meets the strike plate If the mark is too high or low you can easily alter the strike plate The sliding patio door locks protect your home from intruders and if theyre not working correctly you must fix the problem quickly By following these easy steps you can fix the lock on your patio door and get it back to normal in a matter of minutes