pingbuffet9

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/poole-patio-door-repairs-near-me/

Patio Door Lock Repairs Over time patio doors undergo wear and tear which can lead to locks that fail There are a few simple steps you can follow to ensure the security of your uPVC door These easy fixes will ensure your home is secure whether you realign the lock or clean the mechanism Clean the Lock While patio doors are a great way to bring the outside in and keep out the elements however they can also pose an issue for security when your lock isnt functioning as it should Over time wear and tear hot and cold weather dirt and debris can cause your patio door lock to become difficult to operate With a little attention you can ensure that your lock for your patio door is always working in a proper manner Its important to first clean the patio door lock and all moving parts This helps get rid of any grime and coatings that may hinder the lock from functioning in the way it should Begin by wiping down the moving parts of your patio doors lock with a damp cloth then use a scouring pad or rough damp cloth to scrub any difficulttoaccess parts of the door and frame that are ingrained with dirt Then clean the lock with a dry cloth to get rid of any remaining moisture Let it air dry before you use it If you have an exterior door that is fitted with a pin tumbler latch mechanism you can apply lubrication to the lock by applying powdered graphite to the key or applying a Teflonbased lubricant like WD40 MultiUse patio door repairs near me of lubricant is easy to apply and it wont disintegrate with time If youre not able to find the right lubricant for your needs You could use a pencil with an extremely sharp tip Insert the pencil into the lock and move it around a bit to spread the graphite Regular maintenance is also necessary to keep the tracks of sliding patio doors free from dust dirt and other debris They are particularly susceptible to snow ice and other debris which could cause them to get stuck or to bind This could make it difficult for your patio door to open and shut Sliding patio door track rails and rollers can be cleaned by removing any damaged or dirty weather stripping and then cleaning it before reinstalling it The same applies to patio door rollers which can be cleaned and then sprayed with a nonstick lubricant in order to allow them to move freely Lubricate the moving parts uPVC french doors like sliding patio doors operate by using 34 or sometimes fivepoint locking mechanisms which include the lock cylinder and handle controlled by a key These doors also require maintenance including lubrication of the moving parts This can be done with a thin oil never WD40 and should be done every year If hinges that are sagging arent the reason the door could be misaligned and catching or hitting the strike plate hole within the frame Remove the strike plate and employ a sharp tool to enlarge the mortise This will permit the latch to fit into the hole and stop it from rubbing against the frame When the cylinder is out of the way and out of the way measure its width using an object or a piece of wood that fits into the gap of adjustment screw above the lock The outer dimension is measured from the outside of door to the center cylinder The inner dimension is measured from the center adjustment screw to the end of the cylinder Check the locks length If your patio door latch is hard to turn even after oiling and cleaning it could be because its not aligned properly with the strike plate Check if your door is in a balanced position and if the hinge screws are secure In many instances moving the strike plate upwards or downwards can solve the issue Oftentimes the problem occurs when the locks strike is too small for the latch to properly engage In this instance you can widen the opening using an hammer and chisel Then test the latch so that it doesnt touch the jamb frame of the door or get caught on it Before purchasing a new lock you should first determine the mortise type of lock you have This can be done by looking at the end faceplate and noting whether it is square or round Then take a look at the screw holes on the existing lock and note the dimensions of each one This will aid you in finding a replacement that is of the same size and fits perfectly into the hole that you already have Youll need to locate the mortise lock and examine it for scratches bends or other damage that need to be repaired A damaged or bent latch is more prone to break than one thats been utilized often so make sure to replace the lock with a new secure and safe version in the event you notice any signs of damage or wear Once youve inspected the lock and identified which type of replacement youll need its time to start working on the actual repair Take the old handle and spindle from the patio door and then install the new one Begin by installing the handle inside and aligning it with the spindle and then securing it in place with the two screws or bolts which hold it Install the exterior handle following the interior handle Once youve completed these steps then you can test the new handles to ensure they can be opened and closed easily and that the latch locks correctly when you strike the plate Make sure the doors strike is checked The door latch and strike plate are the two parts of the lock that work to ensure that the latch is secure the door An incorrectly aligned strike plate and door latches will result in the latch not being able to latch the door properly This problem is usually very easy to repair First examine the strike plates receiving holes to make sure they are free of obstructions like dirt or plastic plugs Loosen the keeper screws holding the strike plate in position This allows it to move horizontally but not separate it from the frame Adjust the strike plate so that it aligns its holes for receiving with latch hooks of the door latch Once the strike plate is adjusted tighten the screws and test the door to determine whether it locks smoothly after the new adjustment These plates are difficult to reach for homeowners with sliding patio doors However they are vital to secure and unlock your door The metal plates are typically located at the top and bottom of the door jamb where they serve as the doors latch The door latch slides into this strike plate and creates a seal If the strike plate is damaged or rusted or not installed correctly the latch might not lock the door properly One of the most common reasons for the patio door lock to stick or not close is a misalignment of the latch and the strike plate The easiest way to check for this is to perform the lipstick test Apply some lipstick on the outside of the deadbolt and then apply masking tape over it When you shut the door the lipstick will leave marks on the tape indicating exactly where the latch contacts the strike plate If the mark is too high or low you can alter the strike plate Locks for sliding patio doors help protect your home from burglars and if theyre not functioning correctly you should fix the problem quickly By following these easy steps you can repair your patio doors lock and get it back to normal in no time