sawletter3
User Name: You need to be a registered (and logged in) user to view username.
Total Articles : 0
https://www.repairmywindowsanddoors.co.uk/enfield-french-door-repairs-near-me/
Replacing French Door Glass Replacing a damaged pane of glass on a French door is a relatively simple DIY project Cleaning the glass removing trim and molding and then installing the new pane is all thats required French doors feature multiple glass panes that are separated by muntin bars They are also known as Mullions They are available in a wide variety of styles and can be triplepaned to reduce noise and control the glare How to replace a damaged Pane of Glass Wear rubber gloves and safety glasses before you begin to replace the glass This will protect you from any broken glass fragments that may fall during the process Work in an open space such as garages and keep kids away For better access its best to remove the window frame from its ledge However you can still change one pane of glass without having to remove the entire frame With a putty blade use a putty blade to scrape off any old caulking or glazing material around the edge of the window sash Be careful not to scratch the wood molding that holds the window in place as youll need it later to hold the new pane If youre working with a window made of steel the window may be secured by metal glazing points Youll need to remove these as well as the old putty before you can take the pane out of the frame A paint scraper or Chisel can be used but if you find that the putty is difficult to remove gradually soften it using a heat gun Keep the heat gun approximately an inch from the glass and move it back and forth to distribute the heat Place two sheets of aluminum foil on the other panes to stop them from cracking because of the heat Once the old glass has been removed wipe down the inside of the window sash using a damp cloth to clean off any dirt or dust You can now install a new piece glass To cut replacement french doors to size first take measurements of the width and height of the existing opening To purchase a new glass pane that fits into the door frame take these measurements and subtract an eighth inch from each side Many hardware stores will cut a piece of glass for you if you provide the measurement Warm up a few tablespoons of putty and then roll it into a 34inch wide rope Place the putty along the edge of the exposed rabbet and rest the blade of your puttyknife at a 45degree angle against the frame rabbet Move the knife across the glasss edge in a smooth straight line to cut a section of the pane Repeat the process with the other edges of the pane Then scrape off the excess putty Remove the Broken Pane A broken pane in a Frenchstyled door is not just an eye sore but can also pose a risk to safety Replacing a pane of glass in a French door is done in a couple of steps and is generally cheaper than replacing the entire door panel Most homeowners can perform this task on their own however professional assistance is available to those who require special tools or knowhow Begin by removing any broken or cracked fragments of the frame Wear safety goggles and gloves to keep glass shards from getting into your eyes or face Then clean the glass pane opening to get rid of any remaining caulking or putty that was used to keep the old pane in place The next step is to take off the molding or trim that is holding the glass in place This isnt easy since it could require some prying to get the molding out Wearing protective equipment and having a person help you in prying is an ideal idea Label the pieces youre removing so that you can put them back in their original positions Installing the glass is easy once the molding has been removed Take measurements of the glass pane opening and then visit a glass shop to purchase a piece of glass to replace your French door It is a good idea to get a piece of safety glass since it wont break as easily in the event that your French doors break again When you are ready to install your new piece of glass into the opening be sure that it is placed correctly Apply a thin layer of clear silicone caulk on the edge of the glass After the caulk has dried after drying you can put in a new molding If the original nails did not pull through the molding you can hammer in new wire nails to fill in the holes left behind by the old ones The holes should be predrilled to stop the nails from splitting through the molding You can drill holes using tiny bits from the hardware store that is wellstocked Cut a New Pane of Glass Doublecheck the spacing around the frame of the window as well as the edges before ordering an additional pane If you see any gaps you may require adjusting the spring clips or triangles that hold it to the frame Also you must ensure that the new pane is adequate size for your opening if its too large you may experience leaks or other issues after its installed The first step is preparing a work surface Scrape the old compound off the frames sides using a putty blade expose the wood If the frames rabbets are too rough to smooth using a knife lightly sand the edges and apply an exterior primer This will prevent the new glass from absorbing moisture from the wood and will reduce its lifespan After the frame has been cleaned and prepared rub a handfull of putty until it is soft and malleable Apply a thin layer with the putty blade on the inside of the corner rabbets in order to create a narrow bed on which the glass can rest Repeat the process for the other edges of the rabbets Remove any remaining metal points from the grooves of the sash when the putty has dried Wear safety goggles before attempting to remove the points in order to protect yourself from shards of glass A heat gun set to the lowest setting can help you gently warm and loosen the steel so you can bend it out of the frame with pliers When the frame and glass are in place test it by sliding it into the frame Adjust the glass as required before you secure it with spring clips or triangulars made of metal Check that the gap between the frame and the glass is uniform across all sides Test the movement of the window sash and make sure that the new glass does not hinder the closing or opening If you encounter any issues regarding the installation consult an expert who specializes in restoration who can help you restore and maintain your historic home Install the Pane of Glass Before you install the new glass pane It is important to test the fit to ensure that it fits properly Take measurements of the width and height of the window opening by measuring to the outside edge of the L channels Subtract 18 of an inch from each measurement in order to determine the glass size you need Slightly undersizing the pane will make it easier to install and will allow for seasonal expansion and contraction of the wood frame Bring your measurements to an hardware store or home center and have them cut a piece of glass for you You can also cut the glass yourself if you happen to have a large sheet of glass in stock After removing the glass pane clean the window sash grooves Remove any glazing points that were used to support the old pane This can be done using an etype paint scraper or a Chisel If the grooves contain an abundance of putty that has been hardened it is possible to gradually soften it using a heat gun Be careful to cover surrounding windows and moldings with aluminum foil to protect them from the heat It is also possible to use an exterior primer to keep the putty from absorbing its natural oils It is also recommended to clean the grooves of the sash Press a small amount into the rabbets where the glass will be placed At this point the its not about neatness Press the new pane in the rabbets and then move it with your fingers If there are any holes in the wood frame around the glass fill the holes with silicone caulk prior to installing the new glass If the frame has other fastening mechanisms like L channels use a hammer and pry them from the sash grooves Examine the frame for glass fragments that may have shattered during removal and remove them prior to continuing Then apply a layer of clear silicone caulk over the bottom of the frame where it meets the floor to keep water and pests out of the house