shielduse89

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/weymouth-emergency-boarding-up-near-me/

Boarding Up Windows and Doors Before a Storm Hits Boarding up your doors and windows prior to an event can give you an effective protection against damage To do this you must have a few items on the go First measure the width and height of the window including the framing not the surrounding trim or masonry Note these measurements so you dont forget Preparation It is always best to board up windows and doors before an event like a storm or natural disaster strikes This will prevent property damage and minimize loss of life Boarding up windows requires lots of preparation like buying and measuring plywood boards as well as determining the exact dimensions of each window to cover Additionally it takes time to cut the boards and install them correctly Fortunately it is possible to make the process simplified by starting the preparations immediately you learn of a possible storm forming in your area You can avoid stress in the last minute and make it easier for both you and your staff Begin by listening to weather forecasters and following the guidelines set by your local government The earlier you start the process the better as it allows you time to collect and store the needed materials without feeling pressured by a rapidly approaching storm Depending on the severity of the imminent storm you might require large quantities of plywood to cover your windows To ensure you get the right size you can use a tape measure to determine the height and width of each window opening Make sure you consider the framing or trim around each window as well as any extended sills when applicable Divide the total width and the height of your window by 2 to determine the amount of plywood sheets youll require If your window measures a width of 16 inches then the thickness of each sheet is 8 inches If your exterior is made of wood make pilot holes in the plywood sheet to ensure it is aligned with the window frame below This will prevent the possibility of splitting when you screw in the screws For a window opening that is greater than the size of a single sheet of plywood can handle cut two sheets that are each half the size of the desired window and set them sidebyside on the wall Cut a piece 2 by 4 in 51 x 102 cm of lumber to the length of the connecting edge between the plywood sheets and place it on top of the seam Then screw 225 in 57cm screws into the plywood sheet and into the bracing to join the two Materials To ensure security and safety only use materials that are durable and will not break or shatter in high winds The most common material used to encase windows is plywood which is affordable readily available and easy to work with Its important to choose plywood that is specifically designed for exterior use CDX to ensure strength and is free of knots and warping A sturdier option is storm shutters also known as hurricane shutters which are put up over windows that are already in place to provide greater protection against shattered glass and inclement weather Once youve identified the location of your window openings measure the height and width of each to determine the amount of plywood you will need Then make use of a power drill to make pilot holes into the plywood sheets at 2inch intervals around each window Mark the studs on the wall prior to attaching the plywood to ensure that the boards are securely fastened If your home has wood siding search for nailheads that might indicate stud locations You can also use your drill to determine the studs locations Be sure to drive the screws into the framing and not the sheathing or trim a plywood panel fastened only to these materials could be dangerous in winds that are strong If the size of your window is too large for a single sheet of plywood cut two separate pieces that are each the size you require join them using 2 by 4 inch lumber Label each sheet of plywood so you know what window it will be covering Use corrosionresistant screws long enough to penetrate the sheathing and the studs that will be used to join the plywood panels to your wall Try to drive the screws into the studs such that they are half as deep as the plywood is thick but be careful not to go too far and damage the underlying structure of your home You should also consider installing polycarbonate security glass like DefenseLite on your windows that are primary These transparent shields are bonded to the existing glass to guard your windows and doors and are virtually impossible to break preventing criminals from breaking into Installation If you live in a region that is prone to hurricanes or are planning to move to one the best course of action is to secure your windows and doors before the danger of a storm arrives Its a task that can be done quickly and effectively but only if you make the effort to measure and cut then label your plywood panels prior to when the storm hits Youll also require a few other tools including a drill or an hammer and nails if you dont have a power drill and tape a saw an apron gloves and safety glasses Its an excellent idea for the plywood to be coated with sealant in order to make it waterproof Start by measuring the windows height and width Then cut your plywood sheets to fit within the frames This is best done on the spot because you are more in control of the exact dimensions Use a circular saw or track saw to cut the boards to the right size be aware that youll need to sand them down once theyre put in Once the boards are set screw the 3inch stainless steel hanger screws into the posts that frame each window Use washers on each bolt and wing nuts to anchor them Make sure that each screw penetrates the studs at a minimum of two inches to ensure the board is strong enough to withstand high winds If you are building with concrete blocks you can connect the plywood using galvanized pan head screws driven into the overlapping edges of the panels into bricks or cinder blocks You will also need to drill pilot holes into the masonry and then screw corrosion resistant screws into the holes Its a project that could take as long as three hours per window which is why its important to start the process immediately after you hear that a hurricane watch has been issued boarding up commercial property will allow you enough time to complete your project before the storm arrives Maintenance It is recommended to board up your windows and doors before the onset of a severe storm This will help you to avoid costly repairs and protect your home from further damage caused by rain wind debris flying objects and other factors The appropriate materials will make boarding up more efficient and speedier It is important to measure each window precisely This will ensure the OSB or plywood is fitted snugly and will not fall off easily If you are using plywood make sure to use exterior grade sheets and consider adding a second protective finish Mark the locations where the screws will need to be placed into the board after you have taken measurements of the plywood or OSB Then use a drilling machine to predrill holes into the plywood at intervals of 12 inches You can then use hanger bolts to secure the boards in a disaster situation After the storm has passed and youve received allclear from authorities in your area remove the hanger bolts but leave them in place for future emergency situations The next step is to put the plywood panels on top of the windows Be prepared to work in pairs If youre using wood make sure you sand the edges to ensure theyre smooth and wont scratch paint or trim Then use corrosionresistant screws to join the plywood with the pilot holes If your home has vinyl shingles on it then attach the plywood directly to the shingles and not the wood framing A window that has been boarded up may be used to discourage burglars Burglars are more likely target a building that has a damaged or unlocked window Theyre also more likely to break into an establishment thats been boarded up than one that isnt If youre a business owner this is something you should take seriously