shrineside3

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/bifold-door-repairs-caterham/

How to Repair Bifold Door Top Roller Guide If your bifold door is sticking then its likely that they need some maintenance They could need to be cleaned lubricated or adjusted The issue could be caused by a loose screw on the top pivot or the top roller guide This kit contains all the hardware you require to restore your bifold wardrobe door system to its optimal performance Remove the Door Installing an interior set of bifold doors may seem like a complex and complicated project however its actually easy for DIYers with a few years of experience The frame is not the problem but getting the doors to close and fold smoothly is Since bifold doors are complicated machines they might require some tweaking to ensure they are functioning correctly This could be as simple as tightening screws or as complex as removing the door and replacing the pivot pin or roller Most of the time you can fix these issues with a couple of simple adjustments without having to remove the doors You may notice that your doors are sagging or scraping the floor or that they are bouncing off of their track Getting these issues under control isnt difficult and with three easy steps your bifold doors should be back in the blink of an eye The most frequent issue that internal bifolding doors face is the sliding out of alignment This could be due to loose screws or holes in the anchorpivot pins or simply a door that isnt aligned properly In the majority of instances you can fix this with a few easy adjustments however if the door isnt moving it might need to be removed and replaced To open the door youll need an screwdriver and perhaps two pliers to assist in loosening any tight pivot pins The screwdriver can be used to disengage any locking levers on the bottom pivot bracket and the pliers will allow you to wiggle the pin to release it and then take it off After the top roller is removed Once the top roller is removed you can raise the door turn it down and remove it from its track and pivot brackets This is typically quite easy however be careful not to let the door hit against the door frame You should then be able to saw off the edge of the door that is scraping the floor and sand it down until it is smooth Then you can repaint or refinish it as required Take off the Roller Guide This springloaded roller guide mounts on the top edge of bifold doors to aid in smooth operation It is designed to work with Kenna frames and can be fitted to a door panel 1 to 18 inch thick It is constructed of nylon steel and plastic components It is able to replace an old guide To begin removing the guide for the roller remove the screws that hold it in place by using the screwdriver and a little to loosen it After that carefully use your hands to lift it out of the frame This might take some effort so you should have someone else help you keep the door in place while you remove it After the guide has been removed carefully cut the remaining finish on the foot of the new guide using the help of a razor blade to remove it from the rod blank This will make it easier to remove and will ensure that there is no damage to the new guide foot The guide foot is extremely sharp and could cut or nick fingers You may need to apply some force to remove the guide but be careful not to chip or break the foot After removing the old guide remove any threads or epoxy left in the place where it was fixed This will help prevent future problems with the guide After removing the guide you can test the replacement by placing it at its permanent position Make a few turns with masking tape or guide tubing in order to hold it in position This will allow you to double verify the guides spacing and alignment to make sure that everything is properly set up This step is crucial to avoid future problems whether you use the CRB Spine Finder and Deflection System or just eyeball it If the guide is placed correctly and functioning as it should the next step will be to reinstall the door in its place Make sure to replace and tighten any screws or pins that you removed or loosened Remove the Bottom Pivot Bifold doors make a gorgeous addition to any home but sometimes they need a little tweaking or adjustment to remain in great shape Some issues can be addressed by keeping the doors in place Others will require that the doors be removed This guide will guide you through the steps to remove internal bifold door pivots pins and rollers so you can get your doors sliding as new The first step is to gather your tools Making sure you have everything in place prior to time will help you avoid a lot of frustration later on in the project Youll require a screwdriver pliers and perhaps a wrench You can purchase a basic set of tools at your local hardware store for a fair price Keep a supply of wood glue in the back of your hand This can be very useful if you have to fix any rollers back into the correct position Once youve got your tools start by opening the bifold doors Then youll need to loosening the top track bracket with your screwdriver Once this is loose the door should be capable of sliding off the top track completely It may take some jiggling but it should eventually pop off the track The next step is to remove the pivot at the bottom from the frame Close all interior doors before you begin This will be much simpler than working from inside If the bottom track is in good shape youll be able to just lift up the door and then remove the track If the track is damaged youll need to replace it Hardware stores sell replacement tracks for bifold doors as well as swinging closet doors If the track is seriously damaged you may need to replace it completely Now that your track is repaired or replaced it is time to check the doors for the proper operation Make sure that they are capable of moving smoothly between positions Also you should ensure that the edges of the door are parallel to the frame when closed If theyre not youll need to readjust the top pivot bracket and tighten or loosen the bottom set screw until the edge of the door coincides perfectly with the frame Replace the Roller If they are installed correctly they can be used to cover pantries laundry rooms and closets Bifold doors comprise two panels that are hinged and slide down an incline at the top of the frame Over time the roller guide bearings could wear out and cause the doors to sag and scrape against the floor Replacing the guide roller takes only a few minutes and basic tools The first step is to take the guide roller from the door panel This requires removal of the bottom pivot bolt and loosening the screw that holds the guide to its top After removing click here pull the panel off the track Then loosen the bolt that secures the top pivot bolt and use a wrench to remove it from the hole in the top header of the door frame A replacement top nylon roller guide with a 78 inch diameter wheel and a base made of steel is available from Stanley Cox or Acme It can be mounted on the top of bifold doors that range from 1 inch to 138 inches thick and is spring loaded to selfadjust the upper track for smooth glide Another issue with bifold doors is that it scrapes the floor when it closes or opens This can happen after installing carpet or other flooring materials that require the doors to be raised slightly to ensure proper clearance The removal of the pivot adjustment screw on the bottom and loosening the top tracks mounting screws and moving the anchorpivot pin is typically enough to resolve this issue A new set of top roller guides is a cheap solution to a problem that can make bifold doors difficult to operate Theyre usually available at your local hardware store in the door section however they are also available online from a number of sellers In addition to a new top guide for rollers youll require a small bottle of Elmers wood glue that is sold in large box stores and a squeeze clamp The clamp is used to keep the repair area tightly closed after glue is inserted and allowed to dry