snowrubber8

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/bristol-cat-flap-installer-near-me/

It may seem difficult to put up the flap for your cat but with the right guidelines its not all that difficult Firstly determine how high you want the cat flap to be on average belly height Then mark this area on the door and use the template included as a guideline to drill If you have a young kitten hold the door open very slightly and gradually encourage it to enter Reward the kitten every time it moves through Take a measurement of the door A cat flap allows your pet to move into and out of your home at its convenience This can keep your cat in good health as it will ensure that it is getting enough exercise and will also allow it to go back inside when it is stranded outside in bad weather It can also reduce the amount of time you have to let it in or out and will also help protect your home by allowing you to be aware of when it went out However it is essential that the cat flap is fitted correctly to prevent your pet from being able to escape through it or be pushed through by other animals eg dogs It is important to measure the height of your pets belly and the height of the doorway in your home to ensure the flap is at the correct height You can adjust the height of your flap if your cat is taller or smaller than average Next use a spiritlevel to mark the center of the door This is where you will put in the flap Then using the mark as an indication cut out the form of your flap on the door with the help of a jigsaw Once youve cut the area sand the edges of the door to create smooth surfaces You can then drill any fixing holes needed The process of installing the cat flap isnt as difficult as you may think and it shouldnt take more than two hours to finish the entire task from start to finish The process is slightly more complicated if you are required to put it in the case of a uPVC door or composite one This is because composite doors are available in different thicknesses which can impact the way holes are cut This is the reason we recommend calling a professional to complete the task especially in the event that youve never worked with glass before Measure Your Cat A cat flap can spare you from hours of hearing your pets cries for you to let it in or out This is especially helpful if you are at work most of the day and your cat is in the waiting room until you come home in all weathers If you want to fit a cat flap on your door it is essential to take measurements of your cat prior to attempting the task Although it might appear to be an easy task it is crucial to measure the right way or your cat may be unable to use First make sure that your cat is calm prior to taking measurements Youll need to hold them in a manner that they cannot move and make sure that the measuring tape or ruler is flat against their body and not bending in any way Holding the ruler or measuring tape against their body from their head to the bottom of their tail can allow you to get an accurate measurement Once youve got your cats measurements its time to look at the door to determine where to place the flap A good tip is to place the flap on the highest point of your cats stomach as it will allow them to move through it with minimal effort This will also prevent the flap from making a lot noise as it swings back and forth You should also consider the thickness and structure of the uPVC door or composite While timber doors are all of the same thickness uPVC and composite doors may differ in their overall structure and this can make the installation of a cat flap more complicated as you will need to make sure the hole you cut is the right size for your pet It is also worth reading through the directions that come with the cat flap kit to find an outline of the template that can be used to mark out the position of the hole in the door This will enable you to determine where the hole should be located and make sure that the template is positioned properly on the door Utilizing a spirit level to ensure that the template is sitting flush against the door will also be very helpful Cut the Flap You will need to cut an opening in the door panel to install your cat flap prior to you can attach it This can be a tricky job and it is recommended that you get help from an expert cat flap fitter for this job in case you dont have the skills or experience to tackle it yourself You can also refer to the instructions provided with the kit to learn how to do it right You can use the height of the cats or kittens stomach as a guide As a general rule place the cat flap approximately 1015 centimeters above the ground This is the average height of the belly for cats This will let your cat pass through the flap easily and will make it difficult for other cats or nosy neighbours to enter or exit Once youve determined the best location for the cat flap to be positioned mark this location on the door using pencil If cat flap installer near me repairmywindowsanddoors has a template put it on top of the door Use the marks on the template to drill holes in each corner Then youll be able cut out the template and replace it with the cat flap If you are installing your cat flap in the form of a door made of wood or uPVC you are able to do it yourself if you feel confident enough to handle a Jigsaw Be careful not to cut through the vertical rails or mullions of your door You can use a jigsaw cut the panel into a square or a circle depending on the design of your cat flap Be patient and dont try to force the jigsaw into cutting faster Once the hole is made carefully fit the flap of cat food into its new home and make sure that it is securely fixed If the flap has screw caps put them on the protruding bolts Once the screws have been installed then sand the rough edges and seal any gaps This will stop the entry of draughts into your home Install the Flap If you have a standard cat flap you can help your pet through it by placing a small amount of cat food on the outside of the door You can also push the cat with sticks or your hand Once your cat has become comfortable walking through the flap it will be capable of walking through the flap as it pleases This will allow you to let it in and out at any time its wanted It is possible to fit a cat flap in the UPVC doors or glass door but it might not be as simple as putting one in a wooden external door This is due to the fact that the UPVC doors and certain types of glass doors do not have an even thickness This could have an enormous impact on how you cut the flap hole and also whether the flap will fit correctly after installation Depending on the model of cat flap you choose It may include a mounting kit and a template that will tell you exactly where to drill holes for it If the kit doesnt include a template you are able to create one by yourself Its important not to press the jigsaw too in order to cut so it doesnt create a larger than needed hole in your door The majority of cat flaps are square or rectangular in shape however there are some that are circular and they are typically more difficult to place If you have a round flap make sure that the hole is located in the correct place on your door If not your cat may not be able to use it and might be locked outside for the entire day or at night Certain cat flaps have locks that let you control the time your cat is allowed to enter and leave These can be very useful if youre worried about your pet going out at night and coming back in the darkness or if youre working all day The lock can be engaged to allow or deny entry and some locks can be locked in either direction which allows you to close the door completely This is especially beneficial for older or ill cats who dont want to go out in rainy weather