tailtaste0

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/weymouth-emergency-boarding-up-near-me/

How to Go About Boarding Up a Door A door can be boarded up as one way to protect vacant investment properties from the elements While it wont stop all damage it can reduce certain problems that come with severe storms The boarding up of windows and doors can also deter burglars and vandals However it can be expensive and timeconsuming to put plywood boards over the openings in a home Take a measurement of the door The first thing youll need is tape measure It is a good idea to keep a ladder or a chair close to hand in case you need a better view of the top of the frame Wear gloves and goggles if you have to use these tools Begin by taking measurements of the doors width This can be accomplished by running the tape horizontally across the door Be sure to eliminate any additional door parts like a door sweep from the measurement Then measure the height from the floor up to the existing sill or lintel It is essential to measure multiple places particularly with older doors as they may not be a perfect rectangle If the measurements vary take the largest number After youve recorded the width and height measurements then youll have to figure out what size board youll need for the frame It should be at minimum 2 wider and 1 higher than the door 2 higher This will give you enough room to shim both the frame and frame to fit Its a good idea to take off the trim or casing around the jambs of the door to see the studs This will let you measure the exact gap between the frames studs and the edge After removing the trim measure the width of your door frame using a tape measure Take measurements of the frame at three different points and use the smallest measurement It is also important to measure the frames height from top to bottom on both sides Use the shortest measurement for the width of your door If youre having issues with these measurements its a good idea at this point to consult an expert and have them come out to your house to take the measurements for you Theyll tell you the size and type of door you need and how to prepare your frame for a new door Plywood can be cut into pieces A door frame is generally made up of a series thin boards or studs which create a hollow space surrounding the door A typical door is held in place by two hinges that are attached to these studs If you are looking to refinish doors youll have to take it off its hinges over night To stop insects from entering your home and to secure the doors opening a simple method for boarding doors is to place plywood inside the opening It is simple to do without the need to screw or nail the plywood to the door frame Plywood is easy to work with cheap and looks stunning when completed It is the perfect material to use as a temporary fix to a problem in which youre required to remove an existing door to refinish it or put in an entirely new one It can also be used to protect the opening of a room being renovated like a basement or construction site To install boarding up property repairmywindowsanddoors start by measuring the width and height of the door opening Mark the measurements with an utility knife and a straight edge of metal such as the drywall or metal square Then draw a chalkline across each line to mark the area to cut Finally utilize circular saws to cut out the plywood to the desired size When cutting the plywood it is crucial to shield your ears and eyes Wear earplugs or protective goggles when you can In addition its essential to choose a blade that has a wide range of teeth that cut quickly and without tearout Use a small piece of wood to guide the blade Hold it a hairs width away from the line you are cutting A great way to hold the plywood in place without gluing it to the studs is to attach braces that are short at each end Set one brace inside and the other on the outside of the door Then place two 112inch deck screws in each of the holes and tighten them with an openend wrench Secure the Plywood Once you have a sheet of plywood cut to the right dimensions and with the holes for the door frames stiles and rails predrilled and ready to fasten the panel to the door frame This is a relatively easy project that doesnt require a lot of carpentry expertise as long as you follow the right procedures and use the appropriate tools Start by setting up a worktable near the doorway There are two sawhorses as well as 2by4 framing lumber at each end of the table Make marks during the measurement procedure to guide you in cutting the plywood Mark the lines using the help of a utility knife a drywall square or another metal straight edge This will act as a guide to the saw blade and also prevent splintering of plywood when you cut it Wear eye protection and use a circular or table saw equipped with a finetoothed blade cut along the score line Sand the edges of the panel using 120grit paper to smooth it out and remove any burrs After sanding process apply a coat of wood sealer on the plywood panels and let dry as directed by the manufacturer Install the hinges on the frame of the door If youre using a Thinge drill holes on the outside side of your door to accommodate the strap portion of the hinges Then you can screw the outside hinge to the frame with a screwdriver Repeat the process for each hinge on the interior of your door Be careful not to overtighten them or the door could move If you have a single hinged T on your outside door you can make it easier for the latch to close by fishing a wire through the loops on the outside hinges Fold a piece of connect wires in half and then put it through the two holes on the exterior of the door Then twist the wires to lock the door Install the Plywood Place the plywood into the opening of the door using the measurements that you took Move the header top of the frame and the sill bottom Use a level to make sure theres not any slop in the header or sill If the level isnt perfect then put a second shim in the place where needed and continue this procedure until youve got the sill and header to be level Once the plywood is in place fix it using the stainlesssteel hinge bolts and wingnuts Make use of a screwgun that has an attachment for a hex head to prevent removing the heads of the screws While youre there if your house was built with studs that extend through the doorways height drill hanger bolts through the plywood and into the framing studs This is a simpler job than making the hole using a saw for drywall After installing the plywood after installation take measurements of the width and the height of the door opening If necessary cut the bottom of the plywood to fit the dimensions of your door frame and cut two pieces of 1by6 framing lumber as braces that connect to the upper and lower sides of your door Cut along the lines drawn on your plywood using a circular blade fitted with teeth that are finely tipped Wear eye protection Splinters can be removed from the cuts by using a sanding device After you have placed the braces use two pairs of finishing nails of 2 inches to secure each brace to the plywood Once youre done countersink the heads of all nails Cover the braces with a good wood sealing product such as the wipeon polyurethane by Minwax If the door is too big for your doorway you could add an ornamental molding to fill in the gap between the jamb and the door or reduce the size of the opening In most cases however its cheaper and more convenient to buy the door This can also alleviate any problems you may have experienced with the original door if it was damaged and didnt suitable for the opening