tunatenor7

User Name: You need to be a registered (and logged in) user to view username.

Total Articles : 0

https://www.repairmywindowsanddoors.co.uk/southend-emergency-boarding-up-near-me/

Boarding Up Windows and Doors Before a Storm Hits Insuring your doors and windows prior to a storm strikes can provide the protection you need against damage You will need several items to accomplish this Find the width and height of the window including the frame not the trim or masonry that surrounds the window Note these measurements to ensure you dont forget them Preparation It is always recommended to board up windows and doors before a storm or other natural disasters strike This will help prevent damage to property and will minimize the loss of life It requires lots of planning to build a board around windows You have to buy and measure plywood boards and you should be aware of the specific dimensions of each window It takes time to cut and install the boards properly Fortunately it is possible to make the process simplified by starting the preparations immediately you learn of a possible storm forming in your area You will avoid having to rush in the last minute and make it simpler for you and your staff Begin by listening to forecasters for weather and observing the guidelines of your local government The earlier you start the process the better as it gives you enough time to gather and store the needed materials without feeling strained by a fastapproaching storm It is possible that you will require a large amount of plywood to cover your windows according to the severity and speed of the storm To ensure that you have the right size you can use a tape measure to determine the height and width of each window opening Be sure to take into account the trim or framing surrounding each window as well as any sills that are extended if applicable Then calculate the dimensions of the sheets of plywood you require by dividing your windows total width and height by 2 If your window is wide of 16 inches the thickness of each sheet is 8 inches If your exterior is made of wood drill pilot holes in the plywood sheet to align with the window frame below This will prevent splitting when you screw in the screws To make sure that the windows opening is greater than the size of a single sheet of plywood can take cut two separate sheets that are each half the size of the intended window and set them sidebyside on the wall Cut a piece of 2 by 4 inches 51 x 102 cm of lumber to the length the connecting edge between the two sheets of plywood and then place it on top of the seam Then screw 225 in 57cm screws into the plywood sheet and then through the bracing to join the two together Materials To ensure security and safety for security and safety boarding up windows and doors must be done with only strong materials that wont break under pressure or splinter during high winds Plywood is a popular material used to encase windows It is easy to use inexpensive and easily available Its important to choose plywood that is specifically designed for exterior use CDX to ensure strength and is free of knots and warping A stronger alternative is hurricane or storm shutters which are put up over existing windows to provide more protection against glass shattering and the weather that can cause a lot of damage Once youve identified the location of the window openings you can determine the height and width to determine the amount of plywood youll require Use a power drill make pilot holes in the plywood sheets around each window at twoinch intervals Mark the walls with studs prior to attaching the plywood to ensure that the boards are securely fastened If your home is constructed with wood siding look for nailheads that might indicate the locations of studs You can also use your drill to find the locations of studs Make sure you drive the screws into the framing and not the trim or sheathing a plywood panel fastened only to these materials could become dangerous in winds that are strong If the size of your window is too big for a single piece of plywood cut two pieces that are each half the size you require join them using 2 by 4 inches of lumber Label each plywood sheet so you know what window it will cover To secure the plywood panels to the wall use corrosionresistant screws that are long enough to penetrate both the sheathing and studs Aim to drive the screws into the studs such theyre about half the depth of the thickness of the plywood however be cautious not to go too deep and damage the underlying structure of your house You should also consider installing polycarbonate security glass such as DefenseLite on your primary windows These transparent shields are fixed over existing glazing and protect your doors and windows They are virtually indestructible and discourage burglars from gaining entry into your home Installation If you live in an area that is prone to hurricanes or are planning to move to one the best option is to put up a board on your doors and windows before the possibility of a storm is afoot This project can be completed quickly and efficiently however only if the plywood panels are measured cut and labeled prior to the storm Youll also need a few other tools including a drill or nails and a hammer in the event that you dont have the power drill tape a saw an apron gloves and a pair of safety glasses Its also a good idea to allow the plywood to be coated with sealant to make it waterproof Begin by taking measurements of the width and height of each windows opening and then cutting your plywood sheets so they fit within the frames with an overlap of 4 inches on all sides It is recommended to cut the sheets onsite as it gives you more control over the precise dimensions of the plywood Cut the boards to the size you want with a track or circular saw Once installed you will need to sand down all of them Once your boards are in place screw the 3inch stainless steel hanger screws into the framing posts around each window Use washers to secure each bolt and wing nuts Make sure that each screw is able to penetrate the studs at least two inches to ensure the board is strong enough to withstand high winds If youre building using concrete blocks you can connect the plywood with pan head screws galvanized and which are driven into the edges of the panels to the masonry or cinder block boarding up company near me repairmywindowsanddoorscouk will also need to drill pilots into the masonry and then screw corrosionresistant screws into the holes This project can take anywhere from three to four hours per window which is why its essential to begin the process when you learn that a hurricane watch has been issued This will give you plenty of time to finish the job before the storm arrives Maintenance If youre a homeowner or business owner you must have the right materials to secure windows and doors ahead of a severe storm This will help you avoid costly repairs and protect your home from further damage caused by rain wind flying objects and other factors The proper materials will make boarding more efficient and speedier The key is to precisely take measurements of the dimensions of the windows you must cover This will ensure that the OSB or plywood fits well and that it will not be able to slide off easily If youre using plywood make sure you use exterior grade sheets and consider adding an additional protective finish After you have the OSB or plywood measured mark the spots where the screws will go into the board Use a drill to predrill holes at 12inch intervals in the plywood This will allow you to securely fasten the boards with hanger bolts during a disaster or emergency situation After the storm has passed and youve received the allclear by local authorities remove the hanger bolts but keep them in place for any future emergency situations Then you can install the plywood panels above the windows This is a twoperson task So be prepared before you start If you are using plywood be sure to sand the edges of the piece to make them smooth so they wont scratch paint or cut Then make use of corrosionresistant screws attach the plywood using the pilot holes If your home has shingles made of vinyl it then attach the plywood directly to the shingles and not to the wood framing In addition to keeping out water and other weather elements a boarded up window is also a great way to prevent burglary Burglars will target a building that has a broken window or one thats not locked They are also more likely to break in the store with a boarded up window than one that has no If youre a business owner this is a matter you need to consider seriously